Armor Epoxy

The Armor Epoxy is a water-based high gloss epoxy coating offering superior bonding capabilities to interior concrete, and superior protection against damage and deterioration caused by surface abrasion.

• Offers superior bonding capabilities, making it a great primer coat for most coatings
• Can be used as a primer coat, or as a complete floor coating system
• Offers superior protection against damage and deterioration caused by surface abrasion
• Offers superior protection against damage and deterioration caused by foot traffic
• Water based formula is low odor, and low VOC

SURFACE PREPARATION: For a thin film build system (3-10 mils) we suggest either mechanical scarification, acid etching (and then neutralize to 7 PH), or diamond grinding until an appropriate profile is accomplished. For a high build system (over 10 mils), we suggest a fine brush blast (shot blast). To ensure adequate adhesion, the substrate must be free of all dirt, oil, dust, laitance and foreign contaminants. Prior to application a test should be made to determine that the concrete has an acceptable vapor barrier. This can be done by placing a 4’ X 4’ plastic sheet on the substrate and completely taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate does not show signs of eventual hydrostatic pressure problems that may later cause loss of adhesion. However, Armor Epoxy can be applied to a damp floor as long as there are no standing puddles and the dampness is not from a continuous source of moisture due to lack of a vapor barrier. Adhesion tests are recommended prior to using.

PRODUCT MIXING: Pour a full pre-packaged kit of 1 part of Part A to 1 part of Part B together and mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and homogenous. Water Based two part systems need to be mixed well for adequate cure and a streak free finish.

PRODUCT APPLICATION: Apply the mixed material by brush or roller with a 1/4”” nap – 3/8” nap shedless roller cover within the usable pot life time frame, as well as the recommended temperature and relative humidity guidelines listed in the Technical Information section. If continuous outgassing in the concrete is causing bubbles, re-roll the material using a cross rolling method before the material cures to reduce or eliminate air entrapment. If the material becomes thick while applying and sticking to the roller , stop applying and discard the mixed material. At this point it has reached the end of the usable pot life. While applying keep a wet edge to prevent roller marks. It is recommended to work in sections usually using control joints as dividers to ensure proper application results. Do not allow to Puddle! If recoating after 24 hours a light sanding using a fine sanding
screen may be needed to ensure adequate inner coat adhesion.

PLEASE NOTE: Applying Armor Epoxy outside of the suggested parameters may result in job failure. It is always recommended to test the product in a small, inconspicuous area (on the same concrete substrate) for desired results prior to application. Coverage rates may vary for all coatings and substrates depending on porosity, density, texture etc.

The applicator is responsible for suitability of application, and the results of the application. We suggest applying to a test area first to verify compatibility, absorption, coverage rate, and project suitability.

For in-depth up-to-date application instructions, please refer to the Technical Data Sheet and Safety Data Sheet for this product. Documents, videos, and customer photos can be found HERE.

Each 2-Gallon Armor Epoxy kit will cover up to 500 FT2 in one coat, or up to 250 FT2 in two coats.

Please note, the above are coverage estimates. Actual coverage rate will depend on several factors including surface porosity, texture, application method, applicator, etc. This is not a high build coating and excessive build up should be avoided.                               

The Armor Epoxy is a great choice for a variety of interior concrete applications, including:

• Garage floors
• Basement floors
• Warehouse floors
• Shop floors
• Machine shop floors
• Manufacturing facility floors
• Retail floors
  

The Armor Epoxy is designed specifically for unsealed interior concrete floors. Prior to application, the floor must be properly prepped and clean so that the sealer can absorb, bond, and cure.